Vacuum test table with HMI
Leak test station with HMI control. Includes the frame, pneumatics, control panel and programming.
We build the machine
that makes your part.
You bring the problem. We bring the manufacturing engineering.
Process equipment, fixtures and jigs, and automation — from concept to commissioning in your plant, under one signature.
We build for
- Lennox
- BAC
- Carrier
- Denso
- Vertiv
- Shiloh
That manual operation
could be a machine.
Or a fixture. Or a retrofit of the equipment you already have. Which one makes sense depends on volume, floor space and what is running on the floor today — we define that in the on-site survey, before we quote.
Process equipment
Machines and stations designed around a process. From concept to commissioning in your plant.
Press control pedestal
Two-hand control for safe press operation, with a position that adjusts to the operator.
Compressor lift-assist manipulator
Suspended material handling for repetitive loading. Takes the lifting off the operator and reduces damage to the part.
Fixtures & Jigs
Holding, assembly, inspection and gauging fixtures, designed from the customer's part and process.
Automatic brazing fixture
Automatic brazing station with a flexible design: one fixture runs seven part numbers, instead of seven fixtures.
Go/No-Go fixture for endplates
Endplate verification with built-in gauging. Releases the process on the floor every shift, without sending parts to the metrology lab. Less scrap and fewer lost hours.
HVAC brazing fixture
Workholding for manual brazing of HVAC manifolds. Our own design from scratch, marked with the part number for control on the floor.
Automation & controls
Control panels, controls migration and electrical build for new or existing machines.
PLC panel with industrial network
PLC, power supply, industrial switch and labeled terminal blocks, ready to connect to the plant network.
Backplate with VFDs and servo drives
Backplate with VFDs, servo drives and circuit protection, wired and labeled for service.
Control panel with HMI
Panel built with an HMI and push-button station for machine operation, using components stocked by local distributors.
We start before
the drawing exists.
We come to your floor, take measurements and design the complete solution: mechanical, electrical and controls. Most projects start without a drawing — with a sample part, a cycle time that has to come down, or an operation that needs to be taken off the operator.
Every design is reviewed with you before we cut material. And when the original drawing no longer exists, we reverse-engineer it from the part.
Your team reviews the model before we cut material, with operator figures in place to check reach.
Frame, panels, pneumatics and control panel come out of our plant. None of it is subcontracted.
PLC, circuit protection, valves and HMI are built and tested here before shipping. Then we install it, debug and tune it, and train the operator.
01Concept
On-site survey and definition of the solution with your manufacturing team.
02Mechanical design
3D modeling, calculations and fabrication drawings.
03Electrical design
Control schematics, component selection and panel design.
04Fabrication
CNC machining, EDM, welding and grinding in our own plant.
05Control panel
Assembly, wiring and testing before it leaves our plant.
06Programming
PLC, HMI and drives configured for your process.
07Commissioning
Installation, debug and tuning, and operator training.
08Service
Spare parts and support from the same people who built it.
The same plant, working for you
See CNC machining & EDMThe plant that builds our equipment also takes work by the part. Die components — punches, dies, forming inserts, inserts and wear parts — plus machine spare parts, to print or from a sample part.
When the original drawing no longer exists, we reverse-engineer it and deliver the spare part with its model.
Die componentsPunches, dies, forming inserts
Precision CNC machiningMilling and turning
Wire EDMWire-cut EDM
EDM hole drillingSinker EDM on request
Machine spare partsTo print or from a sample part
We build in-house
what we install
Laurel 1616, Col. Moderna, Monterrey, N.L., Mexico. Fabrication is not subcontracted, so lead time and tolerances stay under our control.
CNC equipment
- 1Fanuc Robocut wire EDMα-1iA
- 1Mitsubishi wire EDMFX10
- 1Charmilles EDM hole drillHole drilling
- 2Daewoo CNC lathePuma 10 HC
- 2Mori Seiki machining centerMV40
- 1Hyundai WIA machining centerVX500 · 4-axis
- Hurco machining centerVMX-24
- Hardinge Conquest GTSuper Precision
Conventional equipment and processes
- 1Knee mill
- 1Cylindrical grinder
- 2Surface grinder12″ × 20″
- 1Band saw
- 1Shot blasting machine
- WeldingMIG and TIG
- Panel buildingControl and power
Tell us what needs solving
A drawing, a photo of the part, or a description of the problem on the line. That is enough to start.
Email
ventas@maquinadosyproductos.comOpens with the fields pre-filled
Phone
+52 81 8706 7945Monday to Friday, 9 a.m. to 6 p.m. (Monterrey time, CST)
WhatsApp
+52 81 8706 7945@maqprod.mx · fastest for drawings
Plant
Laurel 1616, Col. ModernaMonterrey, N.L. 64530, Mexico
What happens next
We reply within one business day with scope and an estimated lead time. If the project calls for it, we visit your plant to measure before we quote. The design is reviewed with you before we cut material.